Marvin/L10/210/SV/IV

To complete the clause, select the appropriate wording from below. Highlighted text can be ‘dragged and dropped’ to save typing.

L10 WINDOWS/ ROOFLIGHTS/ SCREENS/ LOUVRES

210 WOOD WINDOWS

Marvin Architectural manufacture a range of high quality wood windows.
Click on the name below to jump to the product and specification details.

Marvin Wood Casement (side opening) Window
Marvin Wood Awning (top opening) Window
Marvin Composite Aluminium Clad / Wood Sliding Sash Window

Marvin Wood Casement [side opening] Window

A range of custom designed casement windows crafted from clear, blemish-free wood with a polished pebble finish.
Marvin Architectural provide a turn-key service from design and specification through to project management and installation. It is recommended that Marvin Architectural is consulted early in the design process.
Marvin windows and doors have been tested to the following standards:
Marvin casement windows have been tested to 2,400 Pa.
BS 6206:1981 – Flat glass for use in buildings.
BS EN 1026 and 1027 – Weathertightness
BS EN 12211 – Resistance to wind loads.
They have also been designed to comply with the recent amendments of the Building Regulations including:
Part B: Fire Safety
Part E: Resistance to the passage of sound
Part F: Ventilation
Part L1: Conservation of fuel and power in dwellings
Part L2: Conservation of fuel and power in buildings other than dwellings
Part M: Access and facilities for disabled people
Sound reduction: Standard double glazing will achieve 28dB sound reduction. Optional glazing systems are available to achieve 34dB and in excess of 40dB with the use of the storm screen/combination storm screen.
Marvin wood windows have been approved by planning authorities for use in conservation areas and up to grade 2 listed buildings.
Thermal values and light transmittance are dependent on the type of glazing selected.
Contact Marvin Architectural Technical Design Department for further details.

Marvin Wood Casement [side opening] Window standard sizes:

Any combination of the following heights and widths.
Frame height:
611mm, 814mm, 916mm, 1018mm, 1221mm, 1424mm, 1526mm, 1627mm, 1830mm.
Frame width:
406mm, 508mm, 610mm, 711mm, 813mm, 914mm.

Wood Casement custom sizes:

Marvin Architectural can provide windows manufactured to custom sizes within the following minimum and maximum sizes.

Minimum frame width: 368mm, minimum frame height: 341mm.
Maximum frame width: 939mm, maximum frame height: 2147mm.

Mulled windows:

Marvin Architectural can link window units in a number of combinations, all with consistent sight lines.

Bay windows:

Casement windows can also be assembled into 30°, 45°, 60° or 90° Bay Windows.
Custom angle assemblies are also available.
Consult with Marvin Architectural for details.

Bow windows:

Curved bow windows are available in both custom and standard variations and sizes.
Consult with Marvin Architectural for details.

Picture Units

Picture Units are fixed glazing units of larger sizes designed to have corresponding sightlines to the casement range. See details below.

Standard size picture units:

Frame height:
611mm, 814mm, 916mm, 1018mm, 1221mm, 1424mm, 1526mm, 1627mm, 1830mm.
Frame width:
1016mm, 1219mm, 1422mm, 1524mm, 1626mm, 1829mm.

Custom size picture units:

Marvin Architectural can provide windows manufactured to custom sizes within the following minimum and maximum sizes.

Minimum frame width: 279mm, minimum frame height: 311mm.
Maximum frame width: 2641mm, Maximum frame height: 2641mm.

Frame:

Frame width: 116mm. Frame thickness: 30mm.
Ponderosa Pine wood interior and exterior.
Also available in Mahogany and Douglas Fir.

Sash:

Operating and transom unit sash thickness: 44mm.
Offset hinge of operating sash allows cleaning from the interior.
Ponderosa Pine wood interior and exterior.
Also available in Mahogany and Douglas Fir.

Interior and exterior finish:

Bare or primed interior or exterior.
Marvin Architectural do not recommend a bare exterior.
A fully finished option is also available.
Consult with Marvin Architectural for recommendations and details.

Operating hardware:

Roto-gear with zinc base, steel drive and gear arms with an ABS operator cover.
Handles: Die-cast, zinc folding handle standard.
Colour: Satin Taupe.
Optional: Bronze, White, Brass, Antique Brass, Oil Rubbed Bronze, Polished Chrome and Satin Chrome.
Locks: One concealed lock on units smaller than series 32 height. Two concealed sequential locks on series 32 heights and taller.
Alternative hardware available as an option. Consult Marvin Architectural for details.

Weatherstrip:

Operating units: Dual bulb and leaf weather-strip at frame and sash.
Colour: Beige Optional: Black

Jamb extensions:

Ponderosa Pine wood interior extensions available for various wall thickness factory applied, finish to match interior. Also available in Mahogany and Douglas Fir.

Insect screens:

Aluminium screen: Full screen, standard frame colour: Satin Taupe
Optional: Bronze or Stone White
Wood screen optional. Frame surround finish: Bare or Primed.
Screen mesh: 18 by 16 mesh. Screen type: Charcoal fibreglass, Charcoal aluminium wire, Black aluminium wire, Bright aluminium wire, Bright bronze wire.

Removable interior wood grilles (glazing bars):

Bar: Ponderosa Pine, 19mm or 29mm wide bars.
Also available in Mahogany and Douglas Fir.
Pattern: Rectangular or custom lite layouts available, contact your Marvin representative.

Interior/Exterior Glazing Bars (Simulated Divided Lites):

Surface applied interior and exterior bars to simulate true glazing bars with double glazing.
Interior bar: Ponderosa Pine wood, 16mm, 22mm or 29mm wide bars, finish to match interior. Also available in Mahogany and Douglas Fir.
Exterior bar: Ponderosa Pine wood, 16mm, 22mm or 29mm wide bars, finish to match exterior. Also available in Mahogany and Douglas Fir.
Pattern: Rectangular, Georgian, Victorian, Queen Anne, Radius, Gothic and custom lite layouts available, contact your Marvin representative.
Optional aluminium spacer bars (between glass panes) available to further simulate an authentic appearance.

Authentic Glazing Bars (Authentic Divided Lite):

Bar: Interior and exterior pine wood, insulated glass 43mm wide bars, finish to match interior and exterior. 22mm wide bars also available for single glazed windows only.
Pattern: Rectangular, Georgian, Victorian, Queen Anne, Radius, Gothic and custom lite layouts available, contact your Marvin representative.

Glass and glazing:

Glazing method: Double glazed with warm edge spacer bars, Single glazed, or Single glazed with secondary glazed panel.
Glazing seal: Silicone glazed, to provide additional security and eliminate visible glazing seals between glass and wooden beading.
Standard glazing type: Softcoat Low E II with Argon (to meet Part L requirements).
Optional glazing types: Clear, Laminated, Tempered, Obscure, Bronze tint, Gray tint, Reflective Bronze and Hardcoat Low E.
Glazing will be altitude adjusted for higher elevations, capillary tubes are optional. Consult with Marvin Architectural for recommendations and details.
Custom glazing capabilities also available for individual project needs.

Accessories:

Installation brackets: 162mm, 238mm or 390mm.
Masonry brackets: 152mm or 254mm.
A wide range of standard exterior casing designs such as Brick mould casing, Stucco casing, or Flat casing and many other options also available.
Consult Marvin Architectural for further details.
A wide range of standard interior plinth blocks and architrave are available.
Consult Marvin Architectural for further details.

Preservative treatment:

WOODTREAT MB is a clear water repellent wood preservative which has been specially formulated by Kop–Coat, Inc. for the treatment of millwork prior to factory or field priming, painting, finishing. It penetrates into the wood to provide effective long–term protection from moisture, mould, mildew, decay and wood destroying fungi which would adversely affect the appearance and/or serviceability of the millwork.
A biodegradable additive also manufactured by Kop–Coat, Inc., is added to the WOODTREAT MB for protection against termites, carpenter ants, beetles and other wood destroying insects.
Consult Marvin Architectural technical literature for details.

Manufacturer:

Product reference:

Casement Window (Wood side opening window unit), complete with internal cleaning facility.

Guarantee:

Ten Year Transferable Warranty on windows and doors and Twenty Year Guarantee on all double glazing seals

Frame:

Sash:

Operating and transom unit sash thickness: 44mm.

Sub-sill:

Included in overall frame height – consult with Marvin Architectural for recommendations and details.

Species:

Ponderosa Pine – Standard wood.

Quality:

Knot and defect free.

Preservative treatment:

WOODTREAT MB clear water repellent wood preservative combined with TIMBERTREAT 6WT biodegradable addirtive.

Finish as delivered:

Bare wood / Factory primed for site decoration.
A fully finished option is also available. Consult with Marvin Architectural for recommendations and details.

Glazing details:

Glazing type:

Standard: Softcoat Low E II with Argon
Options: Clear
Tempered
Laminated
Obscured
Bronze Tint
Grey Tint
Reflective Bronze

Glazing method:

Double glazed units with warm edge spacer bars

Glazing seal:

Concealed factory fitted silicone glazed.
Consult with Marvin Architectural for recommendations and details.

Ironmongery / Accessories:

Standard ironmongery comprising roto-gear handle operation with sequential side locking mechanism.

Colour:

Satin Taupe – Standard finish.

Accessories:

Weatherstrip:

Operating units: Dual bulb and leaf weather-strip at frame and sash
Colour: Beige
Picture units: Continuous weather strip at perimeter.

Jamb extensions:

Interior extensions to suit most wall thickness, which can be factory applied and finished to match interior.

Insect screens:

Aluminium screen:

Standard frame colour: Satin Taupe: Optional: Bronze or Stone White.
Wood screen:
Frame surround finish: Bare / Primed.
Screen mesh: 18 by 16 mesh.
Screen type: Charcoal fibreglass / Charcoal aluminium wire / Black aluminium wire / Bright aluminium wire / Bright bronze wire.

Interior / Exterior Glazing Bars (Simulated Divided Lite):

Interior bar: 22mm / 29mm wide bars.
Finish: To match interior.
Exterior bar: 22mm / 29mm wide bars
Finish: To match exterior.
Pattern: Rectangular

Exterior wood casings:

50mm flat casing.
Consult Marvin Architectural for further details.

Fixing:

As clause 780

Installation brackets:

162mm / 238mm / 390mm

Masonry brackets:

152mm / 254mm
Consult with Marvin Architectural for recommendations and details.

Marvin Wood Awning [top opening] Window

A range of custom designed awning windows crafted from clear, blemish-free wood with a polished pebble finish.
Marvin Architectural provide a turn-key service from design and specification through to project management and installation. It is recommended that Marvin Architectural is consulted early in the design process.
Marvin windows and doors have been tested to the following standards:
Marvin Wood Awning windows have been tested to 2,400 Pa.
BS 6206:1981 – Flat glass for use in buildings.
BS EN 1026 and 1027 – Weathertightness
BS EN 12211 – Resistance to wind loads.
They have also been designed to comply with the recent amendments of the Building Regulations including:
Part B: Fire Safety
Part E: Resistance to the passage of sound
Part F: Ventilation
Part L1: Conservation of fuel and power in dwellings
Part L2: Conservation of fuel and power in buildings other than dwellings
Part M: Access and facilities for disabled people
Sound reduction: Standard double glazing will achieve 28dB sound reduction. Optional glazing systems are available to achieve 34dB and in excess of 40dB with the use of the storm screen/combination storm screen.
Planning authorities in conservation areas have approved Marvin wood windows for grade 2 listed buildings.
Thermal values and light transmittance are dependent on the type of glazing selected.
Contact Marvin Architectural Technical Design Department for further details.

Marvin Wood Awning [top opening] Window standard sizes:

Any combination of the following heights and widths.
Frame height:
510mm, 611mm, 713mm, 814mm, 916mm, 1018mm, 1221mm.
Frame width:
610mm, 711mm, 813mm, 914mm, 1016mm, 1219mm.

Wood Awning custom sizes:

Marvin Architectural can provide windows manufactured to custom sizes within the following minimum and maximum sizes.
Minimum frame width: 405mm, minimum frame height: 316mm.
Maximum frame width: 1625mm, maximum frame height: 1625mm.

Mulled windows:

Marvin Architectural can link window units in a number of combinations, all with consistent sight lines.

Bay windows:

Awning windows can also be assembled into 30°, 45°, 60° or 90° Bay Windows.
Custom angle assemblies are also available.
Consult with Marvin Architectural for details.

Bow windows:

Picture Units

Picture Units are fixed glazing units of larger sizes designed to have corresponding sightlines to the awning range. See details below.
Standard frame

Standard size picture units:

Any combination of the following heights and widths.
Frame height:
587mm, 791mm, 892mm, 994mm, 1197mm, 1400mm, 1502mm, 1603mm,1807mm.
Frame width:
1016mm, 1219mm, 1422mm, 1524mm, 1626mm, 1829mm.

Custom size picture units:

Marvin Architectural can provide windows manufactured to custom sizes within the following minimum and maximum sizes.
Minimum frame width: 255mm, minimum frame height: 300mm.
Maximum frame width: 2640mm, Maximum frame height: 2655mm

Frame:

Frame width: 116mm. Frame thickness (including sub-sill): 54mm.
Ponderosa Pine wood interior and exterior.
Also available in Mahogany and Douglas Fir.

Sash:

Operating and transom unit sash thickness: 30mm.
Cleaning from the interior is available.
Ponderosa Pine wood interior and exterior.
Also available in Mahogany and Douglas Fir.

Interior and exterior finish:

Bare or primed interior or exterior.
Marvin Architectural do not recommend a bare exterior.
A fully finished option is also available.
Consult with Marvin Architectural for recommendations and details.

Operating hardware:

Roto-gear with zinc base, steel drive and gear arms with an ABS operator cover.
Handles: Die-cast, zinc folding handle standard. Level arm optional.
Colour: Satin Taupe.
Optional: Bronze, White, Brass, Antique Brass, Oil Rubbed Bronze, Polished Chrome and Satin Chrome.
Locks: Two concealed locks on per unit.
Alternative hardware available as an option. Consult Marvin Architectural for details.

Weatherstrip:

Operating units: Dual bulb and leaf weather-strip at frame and sash.
Colour: Beige: Optional: Black

Jamb extensions:

Ponderosa Pine wood interior extensions available for various wall thickness factory applied, finish to match interior. Also available in Mahogany and Douglas Fir.

Insect screens:

Aluminium screen: Full screen
Standard frame colour: Satin Taupe: Optional: Bronze or Stone White.
Wood screen optional. Frame surround finish: Bare or Primed.
Screen mesh: 18 by 16 mesh. Screen type: Charcoal fibreglass, Charcoal aluminium wire, Black aluminium wire, Bright aluminium wire, Bright bronze wire.

Removable interior wood grilles (glazing bars):

Bar: Ponderosa Pine, 19mm or 29mm wide bars.
Also available in Mahogany and Douglas Fir.
Pattern: Rectangular or custom lite layouts available, contact your Marvin representative.

Interior/Exterior Glazing Bars (Simulated Divided Lites):

Surface applied interior and exterior bars to simulate true glazing bars with double glazing.
Interior bar: Ponderosa Pine wood, 16mm, 22mm or 29mm wide bars, finish to match interior. Also available in Mahogany and Douglas Fir.
Exterior bar: Ponderosa Pine wood, 16mm, 22mm or 29mm wide bars, finish to match exterior. Also available in Mahogany and Douglas Fir.
Pattern: Rectangular, Georgian, Victorian, Queen Anne, Radius, Gothic and custom lite layouts available, contact your Marvin representative.
Optional aluminium spacer bars (between glass panes) available to further simulate an authentic appearance.

Authentic Glazing Bars (Authentic Divided Lite):

Bar: Interior and exterior pine wood, insulated glass 43mm wide bars, finish to match interior and exterior. 22mm wide bars also available for single glazed windows only.
Pattern: Rectangular, Georgian, Victorian, Queen Anne, Radius, Gothic and custom lite layouts available, contact your Marvin representative.

Glass and glazing:

Glazing method: Double glazed with warm edge spacer bars, Single glazed, or Single glazed with secondary glazed panel.
Glazing seal: Silicone glazed, to provide additional security and eliminate visible glazing seals between glass and wooden beading.
Standard glazing type: Softcoat Low E II with Argon (to meet Part L requirements).
Optional glazing types: Clear, Laminated, Tempered, Obscure, Bronze tint, Gray tint, Reflective Bronze and Hardcoat Low E.
Glazing will be altitude adjusted for higher elevations, capillary tubes are optional.
Custom glazing capabilities also available for individual project needs.
Consult with Marvin Architectural for recommendations and details.

Accessories:

Installation brackets: 162mm, 238mm or 390mm.
Masonry brackets: 152mm or 254mm.
A wide range of standard exterior casing designs such as Brick mould casing, Stucco casing, or Flat casing and many other options also available.
Consult Marvin Architectural for further details.
A wide range of standard interior plinth blocks and architrave are available.
Consult Marvin Architectural for further details.

Preservative treatment:

WOODTREAT MB is a clear water repellent wood preservative which has been specially formulated by Kop–Coat, Inc. for the treatment of millwork prior to factory or field priming, painting, finishing. It penetrates into the wood to provide effective long–term protection from moisture, mould, mildew, decay and wood destroying fungi which would adversely affect the appearance and/or serviceability of the millwork.
A biodegradable additive also manufactured by Kop–Coat, Inc., is added to the WOODTREAT MB for protection against termites, carpenter ants, beetles and other wood destroying insects.
Consult Marvin Architectural technical literature for details.

Manufacturer:

Product reference:

Awning Window (Wood top hung window unit), complete with internal cleaning facility.

Guarantee:

Ten Year Transferable Warranty on windows and doors and Twenty Year Guarantee on all double glazing seals

Frame:

Width: 116mm. Thickness: 30mm.

Sash:

Operating and transom unit sash thickness: 44mm.

Sub-sill:

Included in overall frame height – consult with Marvin Architectural for recommendations and details.

Species:

Ponderosa Pine – Standard wood. Mahogany and Douglas Fir optional.

Quality:

Knot and defect free.

Preservative treatment:

WOODTREAT MB clear water repellent wood preservative combined with TIMBERTREAT 6WT biodegradable additive.

Finish as delivered:

Bare wood / Factory primed for site decoration.
A fully finished option is also available. Consult with Marvin Architectural for recommendations and details.

Glazing details:

Glazing type:

Standard: Softcoat Low E II with Argon
Options: Clear
Tempered
Laminated
Obscured
Bronze Tint
Grey Tint
Reflective Bronze

Glazing method:

Double glazed units with warm edge spacer bars

Glazing seal:

Concealed factory fitted silicone glazed.
Consult with Marvin Architectural for recommendations and details.

Ironmongery/ Accessories:

Standard ironmongery comprising roto-gear handle operation with a pair of side locking mechanisms.

Colour:

Satin Taupe – Standard finish.

Accessories:

Weatherstrip:

Operating units: Dual bulb and leaf weather-strip at frame and sash
Colour: Beige
Picture units: Continuous weather strip at perimeter.

Jamb extensions:

Interior extensions to suit most wall thickness, which can be factory applied and finished to match interior.

Insect screens:

Interior/Exterior Glazing Bars (Simulated Divided Lite):

Interior bar: 22mm / 29mm wide bars.
Finish: To match interior.
Exterior bar: 22mm / 29mm wide bars
Finish: To match exterior.
Pattern: Rectangular

Exterior wood casings:

50mm flat casing.
Consult Marvin Architectural for further details.

Fixing:

As clause 780

Installation brackets:

162mm / 238mm / 390mm

Masonry brackets:

152mm / 254mm
Consult with Marvin Architectural for recommendations and details.

Marvin Composite Aluminium / Wood Sliding Sash Window

A range of custom designed sliding sash windows crafted from clear, blemish-free wood with a polished pebble finish.
Marvin Architectural provide a turn-key service from design and specification through to project management and installation. It is recommended that Marvin Architectural is consulted early in the design process.
Marvin windows and doors have been tested to the following standards:
Marvin sliding sash windows have been tested to 2,000 Pa.
BS 6206:1981 – Flat glass for use in buildings.
BS EN 1026 and 1027 – Weathertightness
BS EN 12211 – Resistance to wind loads.
They have also been designed to comply with the recent amendments of the Building Regulations including:
Part B: Fire Safety
Part E: Resistance to the passage of sound
Part F: Ventilation
Part L1: Conservation of fuel and power in dwellings
Part L2: Conservation of fuel and power in buildings other than dwellings
Part M: Access and facilities for disabled people
Sound reduction: Standard double glazing will achieve 28dB sound reduction. Optional glazing systems are available to achieve 34dB and in excess of 40dB with the use of the storm screen/combination storm screen.
Marvin wood windows have been approved by planning authorities for use in conservation areas and up to grade 2 listed buildings.
Thermal values and light transmittance are dependent on the type of glazing selected.
Contact Marvin Architectural Technical Design Department for further details.

Marvin Wood Sliding Sash Standard Sizes:

Any combination of the following heights and widths.
Frame height:
838mm, 940mm, 1040mm, 1143mm, 1245mm, 1346mm, 448mm, 1550mm, 1650mm, 1753mm, 1854mm, 1956mm, 2057mm.
Frame width:
543mm, 645mm, 746mm, 800mm, 850mm, 900mm, 950mm, 1050mm, 1150mm.

Wood sliding sash custom sizes:

Marvin Architectural can provide windows manufactured to custom sizes within the following minimum and maximum sizes.
Minimum frame width: 340mm, minimum frame height: 635mm.
Maximum frame width: 1660mm, maximum frame height: 3275mm.

Mulled windows:

Marvin Architectural can link window units in a number of combinations, all with consistent sight lines.

Bay windows:

Sliding sash windows can also be assembled into 30°, 45°, 60° or 90° Bay Windows.
Custom angle assemblies are also available.
Consult with Marvin Architectural for details.

Bow windows:

Curved bow windows are available in both custom and standard variations and sizes.
Consult with Marvin Architectural for details.

Picture Units

Picture Units are fixed glazing units of larger sizes designed to have corresponding sightlines to the sliding sash range. See details below.
Standard frame

Standard size picture units:

Any combination of the following heights and widths.
Frame height:
1040mm, 1143mm, 1245mm, 1346mm, 1450mm, 1550mm, 1650mm, 1753mm, 1854mm, 1956mm, 2057mm.
Frame width:
1050mm, 1254mm, 1356mm, 1560mm, 1762mm.

Custom size picture units:

Marvin Architectural can provide windows manufactured to custom sizes within the following minimum and maximum sizes.
Minimum frame width: 340mm, minimum frame height: 400mm.
Maximum frame width: 2667mm, Maximum frame height: 2667mm

Frame:

Frame width: 116mm(excluding exterior casing). Frame thickness: 17mm.
Ponderosa Pine wood interior and exterior.
Also available in Mahogany and Douglas Fir.

Sash:

Operating and transom unit sash thickness: 41mm.
Tilt-in sash mechanism allows cleaning from the interior. Not available on larger sizes.
Sashes may be removed from the interior for maintenance.
Ponderosa Pine wood interior and exterior.
Also available in Mahogany and Douglas Fir.

Interior and exterior finish:

Bare or primed interior or exterior.
Marvin Architectural do not recommend a bare exterior.
A fully finished option is also available.
Consult with Marvin Architectural for recommendations and details.

Operating hardware:

Sash lock and keeper: open style crescent cam lock with sash release lever, surface mounted.
Optional sash lift or fingerpulls routed into the bottom rail of sash available.
Colour: Satin Taupe.
Optional: Bronze, White, Bronze, Brass, Antique Brass, Oil Rubbed Bronze, Satin Chrome and Satin Nickel.
Balance System: Concealed balance system
Alternative hardware available as an option. Consult Marvin Architectural for details.

Weatherstrip:

Operating units: Continuous foam filled bulb at head jamb, jambs, check-rail and bottom rail.
Picture and Transom Units: Continuous weatherstrip at perimeter: foam filled bulb weather-strip at jamb, head and sill.

Jamb extensions:

Ponderosa Pine wood interior extensions available for various wall thickness factory applied, finish to match interior. Also available in Mahogany and Douglas Fir.

Insect screens:

Aluminium screen: Full screen standard Frame colour: White, Pebble Gray, Bronze, Bahama Brown or Evergreen.
Screen mesh: 18 by 16 mesh. Screen type: Charcoal fibreglass, Charcoal aluminium wire, Black aluminium wire, Bright aluminium wire, Bright bronze wire.

Storm sash and screen:

Wood framed combination storm sash and screen/or wood storm sash available for exposed sites and increased sound deadening.

Removable interior wood grilles (glazing bars):

Bar: Ponderosa Pine, 19mm or 29mm wide bars.
Pattern: Rectangular or custom lite layouts available, contact your Marvin representative.

Interior/Exterior Glazing Bars (Simulated Divided Lites):

Surface applied interior and exterior bars to simulate true glazing bars with double glazing.
Interior bar: Ponderosa Pine wood, 16mm, 22mm or 29mm wide bars, finish to match interior. Also available in Mahogany and Douglas Fir.
Exterior bar: Ponderosa Pine wood, 16mm, 22mm or 29mm wide bars, finish to match exterior. Also available in Mahogany and Douglas Fir.
Pattern: Rectangular, Georgian, Victorian, Queen Anne, Radius, Gothic and custom lite layouts available, contact your Marvin representative.
Optional aluminium spacer bars (between glass panes) available to further simulate an authentic appearance.

Authentic Glazing Bars (Authentic Divided Lite):

Bar: Interior and exterior pine wood, insulated glass 43mm wide bars, finish to match interior and exterior. 22mm wide bars also available for single glazed windows only.
Pattern: Rectangular, Georgian, Victorian, Queen Anne, Radius, Gothic and custom lite layouts available, contact your Marvin representative. Size restrictions.

Glass and glazing:

Glazing method: Double glazed with warm edge spacer bars, Single glazed, or Single glazed with secondary glazed panel.
Glazing seal: Silicone glazed, to provide additional security and eliminate visible glazing seals between glass and wooden beading.
Standard glazing type: Softcoat Low E II with Argon (to meet Part L requirements).
Optional glazing types: Clear, Laminated, Tempered, Obscure, Bronze tint, Gray tint, Reflective Bronze and Hardcoat Low E.
Glazing will be altitude adjusted for higher elevations, Argon gas not used.
Consult with Marvin Architectural for recommendations and details.
Custom glazing capabilities also available for individual project needs.

Accessories:

Installation brackets: 162mm, 238mm or 390mm.
Masonry brackets: 152mm or 254mm.
A wide range of standard exterior casing designs such as Brick mould casing, Stucco casing, or Flat casing and many other options also available.
Consult Marvin Architectural for further details.
A wide range of standard interior plinth blocks and architrave are available.
Consult Marvin Architectural for further details.

Preservative treatment:

WOODTREAT MB is a clear water repellent wood preservative which has been specially formulated by Kop–Coat, Inc. for the treatment of millwork prior to factory or field priming, painting, finishing. It penetrates into the wood to provide effective long–term protection from moisture, mould, mildew, decay and wood destroying fungi which would adversely affect the appearance and/or serviceability of the millwork.
A biodegradable additive also manufactured by Kop–Coat, Inc., is added to the WOODTREAT MB for protection against termites, carpenter ants, beetles and other wood destroying insects.
Consult Marvin Architectural technical literature for details.

Manufacturer:

Product reference:

Sliding sash Window. Complete with internal cleaning facility except on larger sizes.

Guarantee:

Ten Year Transferable Warranty on windows and doors and Twenty Year Guarantee on all double glazing seals.

Frame:

Width: 116mm. Thickness: 17mm.

Sash:

Operating and transom unit sash thickness: 41mm.

Sub-sill:

Included in overall frame height – consult with Marvin Architectural for recommendations and details.

Species:

Ponderosa Pine – Standard wood.
Mahogany and Douglas Fir optional.

Quality:

Knot and defect free.

Preservative treatment:

WOODTREAT MB clear water repellent wood preservative combined with TIMBERTREAT 6WT biodegradable additive.

Finish as delivered:

Bare wood / Factory primed for site decoration.
A fully finished option is also available. Consult with Marvin Architectural for recommendations and details.

Glazing details:

Glazing type:

Standard: Softcoat Low E II with Argon
Options: Clear
Tempered
Laminated
Obscured
Bronze Tint
Grey Tint
Reflective Bronze

Storm sash and screen:

Wood framed combination storm sash and screen/or wood storm sash available for exposed sites and increased sound deadening.

Glazing method:

Double glazed units with warm edge spacer bars

Glazing seal:

Concealed factory fitted silicone glazed.
Consult with Marvin Architectural for recommendations and details.

Ironmongery/ Accessories:

Open style crescent cam lock with sash release lever, surface mounted.
Optional sash lift or fingerpulls routed into the bottom rail of sash available.
Colour: Satin Taupe.
Optional: Bronze, White, Brass, Antique Brass, Oil Rubbed Bronze, Satin Chrome and Satin Nickel.
Balance System: Concealed balance system

Accessories:

Weatherstrip:

Operating units: Continuous foam filled bulb at head jamb, jambs, check-rail and bottom rail.
Picture and Transom Units: Continuous weatherstrip at perimeter: foam filled bulb weather-strip at jamb, head and sill.

Jamb extensions:

Ponderosa Pine wood interior extensions available for various wall thickness factory applied, finish to match interior. Also available in Mahogany and Douglas Fir.

Insect screens:

Aluminium screen:
Full screen standard, half screen optional.
Frame colour: White, Pebble Gray, Bronze, Bahama Brown or Evergreen.
Select and custom colours also available.
Optional full and half screen also available.
Finish: Bare or primed.
Screen mesh: 18 by 16 mesh.
Screen type: Charcoal fibreglass / Charcoal aluminium wire / Black aluminium wire / Bright aluminium wire / Bright bronze wire.

Interior/Exterior Glazing Bars (Simulated Divided Lite):

Interior bar: 22mm / 29mm wide bars.
Finish: To match interior.
Exterior bar: 22mm / 29mm wide bars
Finish: To match exterior.
Pattern: Rectangular

Exterior wood casings:

50mm flat casing.
Consult Marvin Architectural for further details.

Fixing:

As clause 780

Installation brackets:

162mm / 238mm / 390mm

Masonry brackets:

152mm / 254mm
Consult with Marvin Architectural for recommendations and details.